攪拌車輪圈和輪胎的組合事項
全自動攪拌車在使用和購買的過程中都要看重，注重率生產、節能生產一直各大企業比較重視的問題，選擇優良產品注重施工效率的提高，輪胎是一個其作用的部件。下面來講講攪拌車輪圈和輪胎的組合事項吧。
In the process of using and purchasing the fully automatic mixer truck, we should pay attention to the production rate and energy-saving production, which have always been paid more attention by major enterprises. We should choose excellent products and pay attention to the improvement of construction efficiency. Tire is a part of its function. Now let's talk about the combination of mixer rim and tire.
請使用標準攪拌車輪圈，已經變形或這損傷的攪拌車輪圈切勿使用。攪拌車輪圈與攪拌車輪胎組合前，要先清理輪圈和攪拌車輪胎，不可以有雜物留在內部。
Please use the standard mixer wheel. Do not use the deformed or damaged mixer wheel. Before mixing wheel rim and mixing tire are combined, the wheel rim and mixing tire shall be cleaned first, and no sundries shall be left inside.
攪拌車輪圈與攪拌車輪胎組合之前。可以使用橡潤滑劑或著肥皂水擦拭胎唇輪圈凸緣，一定不要使用油性潤滑劑。輪圈與攪拌車輪胎組合時應注意嵌合情形，不要使用超過正常范圍之風壓強行安裝，以免發生危險。
Before the combination of mixer wheel rim and mixer tire. Rubber lubricant or soapy water can be used to wipe the tire lip and rim flange, and oily lubricant must not be used. When the rim is combined with the tire of the mixer truck, attention shall be paid to the fitting situation. Do not use the wind pressure exceeding the normal range to force the installation, so as to avoid danger.
輪圈與攪拌車輪胎組合需要由攪拌車輪胎行專門人員來操作，請勿自行組合。
The combination of wheel rim and mixer tire needs to be operated by special personnel of mixer tire line. Do not combine by yourself.
假如攪拌車輪胎運用日久，外胎銹死在輪圈內而不容易取下時，能夠?qū)⑤喬テ椒旁跐崈舻目罩猩?，用撬棒在胎口與輪圈之間撬開一定間隙，在輪圈與外胎的分離部倒些肥皂水或清水，并用鐵錘沿l輪圈外側稍加錘擊，使水在振動的過程中從縫隙處滲入生銹面，待浸透后外胎便容易拆下來。
If the mixer tire is used for a long time and the outer tire is rusted in the rim and is not easy to remove, the tire can be placed flat in the clean air, pry a certain gap between the tire mouth and the rim with a crowbar, pour some soapy water or clean water into the separation part between the rim and the outer tire, and hammer slightly along the outside of the L rim with a hammer to make the water penetrate into the rusty surface from the gap in the process of vibration, and the outer tire can be easily removed after being soaked.
此外輪胎氣壓應按使用說明書的要求合理充氣，即同一軸上的兩個輪胎氣壓必須相同；當輪胎出現異常磨損時，應立即查明原因。定位失準和轉向機構技術故障是異常磨損的主要原因。車輪動平衡不良、超載等因素也是輪胎異常磨損的原因。
In addition, the tire pressure shall be inflated reasonably according to the requirements of the operation manual, that is, the pressure of two tires on the same axle must be the same; In case of abnormal tire wear, find out the cause immediately. Misalignment of positioning and technical failure of steering mechanism are the main causes of abnormal wear. Poor wheel dynamic balance, overload and other factors are also the reasons for abnormal tire wear.
全自動攪拌車廠家提醒您，可以通過觀察輪胎花紋深度，正常磨損到極限的輪胎也要及時更換和更換。如果車輛在一般道路上行駛，輪胎花紋深度小于1.6mm，在高速公路上行駛時，輪胎花紋深度小于2.4mm。這是輪胎更換的表現；輪胎更換應配對；胎紋中的雜物要及時清除。
The manufacturer of full-automatic mixer truck reminds you that you can change and replace the tires that are normally worn to the limit in time by observing the tread depth of the tires. If the vehicle runs on ordinary roads, the depth of tire tread is less than 1.6mm, and when driving on highways, the depth of tire tread is less than 2.4mm. This is the performance of tire replacement; Tire replacement shall be matched; The sundries in the tread shall be removed in time.
攪拌車輪圈和輪胎的組合事項以及輪胎的其他事項就講解完畢了，更多詳細的要點或者細節問題就來關注我們的網站www.jbckj.cn吧，讓您獲取到多多的有效的信息！
The combination of mixer wheel rim and tire and other matters of tire have been explained. For more detailed points or details, please pay attention to our website www.jbckj.cn COM, let you get a lot of effective information!
