中科混凝土攪拌機加潤滑油有哪些要注意的？
在中科混凝土攪拌機中加入潤滑油，可以有效地減少混凝土的磨損，提高構件的使用壽命。但是，用戶在向攪拌機中添加潤滑油時應注意以下事項。
Adding lubricating oil into the concrete mixer of Zhongke can effectively reduce the abrasion of concrete and improve the service life of components. However, the user should pay attention to the following when adding lubricating oil to the mixer.
1. 混凝土攪拌機在使用過程中不得檢查和潤滑。
1. The concrete mixer shall not be inspected and lubricated during use.
2. 使用混凝土攪拌機后，在各潤滑點適當添加必要的潤滑油(滾筒軸、滾筒、鋼絲繩等運動部件)。
2. After using the concrete mixer, add necessary lubricating oil (roller shaft, roller, steel wire rope and other moving parts) at each lubricating point.
3.定期在每個接頭上加黃油，每4小時注入潤滑油密封軸端，每周排放一次污水。
3. Add grease to each joint regularly, inject lubricating oil to seal shaft end every 4 hours, and discharge sewage once a week.
4. 混凝土攪拌機減速器的齒輪和軸承由齒輪轉動，使油飛濺到箱體內壁上潤滑。減速機的油位應保持在油量表的兩條線之間。油位過高或過低都會導致各部件溫升或潤滑不良，增加功率損耗，導致機器運轉不良。在新機器開始運行后的個150和300小時內應該更換機油，以在測試運行期間沒有完全清洗的污垢。工作時，應經常檢查油位，并及時加油。
4. The gear and bearing of the reducer of the concrete mixer are rotated by the gear to make the oil splash to the inner wall of the box for lubrication. The oil level of the reducer shall be kept between the two lines of the oil gauge. If the oil level is too high or too low, it will cause temperature rise or poor lubrication of all components, increase power loss, and cause poor operation of the machine. The oil should be changed within the first 150 and 300 hours after the new machine starts to run to remove dirt that was not completely cleaned during the test run. During operation, the oil level shall be checked frequently and oil shall be added in time.
5. 所選用的潤滑油應具有一定的購買粘度和粘度溫度、冰點低、氧化安定性好、無機械雜質和水分、無腐蝕磨損材料等特點。常用汽油機機油的運動粘度為100℃，分為6級、10級、15級、8級增稠、8級低凝、8級合成增稠等。等級越高，粘度越高，質量指標應符合標準規定。向混凝土攪拌機中加入油不是一件小事。用戶應重視并正確添加，以保證攪拌機的正常運行。
5. The selected lubricating oil shall have certain purchasing viscosity and viscosity temperature, low freezing point, good oxidation stability, no mechanical impurities and moisture, no corrosive wear materials, etc. The kinematic viscosity of commonly used gasoline engine oil is 100 ℃, which can be divided into six grades, ten grades, fifteen grades, eight grades of thickening, eight grades of low condensation, eight grades of synthetic thickening, etc. The higher the grade is, the higher the viscosity is, and the quality index should meet the national standard. Adding oil to a concrete mixer is not a trivial matter. The user should pay attention to and add it correctly to ensure the normal operation of the mixer.
以上是中科混凝土攪拌機廠家為大家介紹的相關內容，想要了解更多內容，歡迎訪問網站：http://jbckj.cn
The above is the relevant content introduced by the concrete mixer manufacturer of China Science and Technology Co., Ltd. for more information, please visit the website: http://jbckj.cn
